« Handy Tips on buying Lawn Mower Parts | Home | Electric Lawn Mower & greenhouse gases »
How to sharpen lawn mower blades
By Abbey | August 24, 2010
How to sharpen lawn mower blades
Is your lawn mower cutting the grass blades of grass instead of tearing it? Does your lawn look like it was eaten by a goat, despite the cut by the lawnmower? Wait, do not you pull your hair from the root. Help is at hand. We will show you how to sharpen the mower blades and minimum effort.
Your manual mowers – Walk behind The Faithful
Tools: The tools, which will be for this Job need are
– you and your time of 2 hours or less
– a bastard file of about 12 “long
– A small crow bar to the movement of the rotor of lawn mower.
– A desk is dong the job comfortably useful.
How to: You may receive the following general approach Directive apply and make changes to suit you. Remember, the procedure is not sacrosanct. The results are important, not the procedure.
remove first If possible, the lawn mower and place Lawnmower handle on the table.
2 Secure it in the brackets if possible. If you are no brackets, no effort to secure it against any block, so that the movement is restricted away from you.
3 Fix the crowbar in the blades, so it does not turn
4 With the help of the bastard file, file the edges of the leaves, so they sharply . work at an angle of 45 degrees
5 If one blade is sharpened, remove the crowbar and turn the rotor to work on another story. Repeat the process until all the blades are sharpened.
6th If you have a flexible shaft grinder in your DIY workshop, you will be able to complete work within 5-10 minutes per blade. Make a template of blade profile before your work and often begin to compare. This is necessary to ensure that you do not cut in one place.
Safety tip for you
While sharpening the blades ensure that the line not to long, otherwise
, you can get hurt.
Sharpen Mower Blades Of Power
more. We have general statements in this procedures involved, one would change the procedure slightly. Keep the maintenance manual of lawn mower handy if you have one.
tools required.
– siphon hose and clean container
– Heavy work gloves and safety glasses
– Double-Cut (medium-rough) flat file
– Lumber scrap
– Socket
– Rubber Hammer * />
– vise or C clamps />
– Rotary knife grinder accessories />
– Drill * />
– screwdriver or 1/4-in. rod or bolt *
– Blade Balancer
– Replacement blade *
* Only Requirements
The list may look formidable, but tools are generally well with any home improvement.
procedure:
The method is simple single blade mower given, but the same applies to all types of knives apply regardless of whether single or double
– Wear gloves and clean the engine and the fuel tank from the outside
– Remove spark plug from the engine
– Remove all the fuel from the tank of the gasoline engine. Use the vacuum hose so that you do not spill gasoline do on the ground.
– you completely drain the oil from gearbox if you have a
– reversing the engine and have access to the blade.
– Attach the motor is not moving so and clean the blade area thoroughly
– Remove with the help of a socket wrench, remove the nut holding the blade. Usually the mother will be unlocked in order to reverse the motor direction . You can use the screwdriver into the fan motor lead the rotation of the engine to stop.
– If you find that you have too much to be found by force to unlock the mother, one or two drops of rust remover chemical, and try after 30 minutes
– After you remove the knife, lock it in a vise and sharpen it with a file or a grinder. Sharpen only the outer 2-3 inches. The area known to be sharpened, if you have to see the knife.
– Sharpen only to the extent necessary. Too much focus is required. This is not the knife. It works with the speed of the motor
– After sharpening, check with your thumb. Be careful not to cut thumb. When you have finished sharpening seen before or someone to do it, you will know what we mean.
– Balance the blade with a small balancing tool on VEE blocks, or even on two foot rulers side by side
– Replace the blades, refill engine oil and gasoline and test the sharpness of blades on uncut portion of your lawn
safety tips:
– Always use safety goggles and gloves when working with power tools.
– Make sure you remove, the spark plug before. Serious accidents can happen if you do not.
Topics: Blade Lawn Mower | No Comments »
Comments are closed.